Essential Plumber Guide for Installing a Bathtub
Essential Plumber Guide for Installing a Bathtub
Blog Article
The article in the next paragraphs relating to Tools You Need to Install a New Bathtub is relatively fascinating. Don't bypass it.
Installing a bathtub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately challenging task. If the old tub is conveniently available, the task can move speedily; if you have to open a wall to get rid of the old tub and position the brand-new tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to leave the old tub as well as embeded in the new one. See to it you have actually qualified yourself for the job and also are comfortable trying it. Instead of employing a contractor to take over a halfway-completed project, it is much better to consider employing one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will assist you set up a brand-new tub in your restroom if you have currently purchased a new tub as well as don't need to change the setup of your previous water supply pipelines.
Your tools and product checklist ought to comprise the following:
Planning for the Installation
First of all, the supporting structure supplied with the bath must be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the tap includes a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps system to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the limited access that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. Once the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Using the two wooden boards under its feet, place the bathtub in the called for placement. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny factors.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap adapter to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the supply of water and examine all joints and new pipework for leaks and also tighten them if necessary. Fill up the bathtub as well as also examine the overflow outlet as well as the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the producer's user's manual. Tiling as well as sealing around the bathtub must wait till the bathtub has been used at the very least when as this will certainly resolve it into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin making sure that the washers are in place between the faucet as well as the sink. Secure the faucet in place with the maker supplied backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type must be attached to the tap ends initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to crack an inflexible seal, creating the water to permeate the wall between the bath and also the tiling, resulting in complications with moisture and also feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your components as well as installations. They are sold in tubes and cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealant can split relatively very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily readily available on the market. It is advisable to fit the tiles utilizing waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that article on A Step-by-Step Guide to Installing a Bathtub through a friend on a different domain. So long as you enjoyed reading our page please be sure to share it. Thanks for your time. Visit us again soon.
Book Inspection Report this page